Home Asia LFS Links Jurong LFS Map Jurong LFS locations CO2 DIY DIY Brine Shrimp Hatchery Tripod Camera Guppy Breeding Asia LFS Quiz & Contest! Forums Betta Breeding Cutting Acrylics Thank You For Visiting Asia LFS! Feedback Ketapang Leaves Sale


CO2 DIY

 

Navigation Buttons

Home
Asia LFS Links
Jurong LFS Map
Jurong LFS locations
CO2 DIY
DIY Brine Shrimp Hatchery
Tripod Camera
Guppy Breeding
Asia LFS Quiz & Contest!
Forums
Betta Breeding
Cutting Acrylics
Thank You For Visiting Asia LFS!
Feedback Ketapang Leaves Sale

 

 

Do-It-Yourself CO2 System!

Schematic:

Fermentation Equation:

Sugar + Yeast -> Ethanol + ‘Carbon Dioxide?#060;/font>

 

 

Please read the [Disclaimer] before you begin.

 

 

***********************************

Building the CO2 Generator:

***********************************

1) Total List of Equipments Needed.

List of Equipments

2) Create a hole on each of the 2 bottle caps. 

(slightly bigger than air tube will do).

(Please be careful with any sharp objects, wear a glove if need be)

 

Read Safety Instructions HERE

 

3) Seal the holes with Silicon Gel.

(Wait for it to dry within 24 hours)

Precautions: Please keep silicon gel after using

 

4) The completed setup of CO2 Generator.

(with 1 air tube connector + 1 air valve)

Can fill the bottles with Yeast + Water + Sugar to produce CO2.

 

 

***********************************

Building the CO2 Reactor:

***********************************

1) Cut 4 pieces of "thin air tubes" from other fish accessories.

 

 

 

2) Creating a 'tiny hole' in a plastic tube.

 

 

(Please be careful with any sharp objects, wear a glove if need be!)

 

Read Safety Instructions HERE

 

 

3) Glue the tiny air tubes to the holes with silicon gel.

 

 

 

4) Glue with the aid of a needle as a support & to prevent silicon gel from flowing into the holes.

 

 

5) Four needles supporting the 4 tiny air tubes to the plastic tube.

 

 

6) Under Construction.

 

(under construction..)

 

 

7) Under Construction..

 

(under construction..)

 

 

Things you need:

2 Mineral water bottles (250ml)
Air tube (~60cm)
Silicone Sealant
2 Air tube Connectors (L & T-Shapes)
A Sharp Object (for creating a hole in bottle cap)
A Pair of Scissors
1 Cork
1 Tubefix worms holder
1 Plastic Tube
4 Needles (depends on number of holes created)
 
Yeast (used for baking cake ~ S$1.90 for 5 packets)
Sugar + Water

Back to TOP

Safety Devices Required:

Goggles/Spectacles
Hand Gloves
Medical Kit

Precautions:

Always Wear a pair of goggles
Always Wear a pair of hand gloves!
Always Keep  sharp objects away after use!

Always Have a medical kit around!

NEVER do this project when a child is around!
NEVER attempt this project if you are under 12 years old!
NEVER place the silicon gel near a child or fish/pets!
NEVER say you cannot do this project! If Alan can, so can you! ;)

Back to TOP

Disclaimer:

The author of this website should not be held responsible for any mishaps or losses as a result of following the instructions here. 

Back to TOP

 

 

 

 

 

Home ]

Send mail to [email protected] with questions or comments about this web site.
Copyright ?2002 Asia LFS
Last modified: May 17, 2002
Hosted by www.Geocities.ws

1